Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Registry nameRegistry typeInstaller propertyDefault valueDescription

AltPxeClientPort

REG_DWORD

This value does not have an installer property.


Registry value is not created.

This registry setting is relevant only on the Responder.

Multiexcerpt
MultiExcerptNameAltPxeClientPort

This is the UDP port that the PXE Everywhere Agent will reply to the PXE client (alternate boot loader) on.

If this registry setting does not exist then port 2068 is used.


AltPxeServerPort 

REG_DWORD

This value does not have an installer property.


Registry value is not created.

This registry setting is relevant only on the Responder.

Multiexcerpt
MultiExcerptNameAltPxeServerPort

This is the UDP port that the alternate boot loader will broadcast the custom PXE request on. The PXE Everywhere Agents must be configured to listen on this port, so it must be the same port defined by DHCPPORT when installing the PXE Everywhere Agent.

If this registry setting does not exist then port 2067 is used.


BindTo

REG_SZ

This value does not have an installer property.


Registry value is not created.

Comma-separated list of IP addresses which PXE Everywhere Agent listens for DHCP (PXE) and TFTP requests. If not present, PXE Everywhere Local listens on all IP addresses. Use this if there is more than one network interface.

Debug

REG_DWORD
DEBUG
1


Multiexcerpt
MultiExcerptNameDebug

The debug level. Leave this at 1 unless 1E Support recommends a change. The range is:

  • 0x1: Basic logging
  • 0x4: Extra "application-specific" logging
  • 0x8: Extra registry logging
  • 0x10: Increased general logging

The following two bits will perform centralized logging via SOAP calls to the PXE Central Server:

  • 0x1000: Logs election results
  • 0x2000: Logs TFTP file transfer start and stop (includes statistics).


DefaultBlockSize

REG_DWORD

This value does not have an installer property.


Registry value is not created.

Default TFTP block size. 512 if not specified.

DhcpPort

REG_DWORD
DHCPPORT
67


Multiexcerpt
MultiExcerptNameDhcpPort

Do not use the DHCPPORT installer property on Responders, where DhcpPort must always be 67.


ElectionWaitSecs

REG_DWORD
ELECTIONWAITSECS
1


Multiexcerpt
MultiExcerptNameElectionWaitSecs
Time (in seconds) to wait for responses to the election request before broadcasting the result. Can be any positive integer value above 0.


ElectionWeight

REG_DWORD
ELECTIONWEIGHT
50


Multiexcerpt
MultiExcerptNameElectionWeight
When set, this manually created registry value determines the likelihood of the machine winning elections, all else being equal. The value must be between 0 and 99 inclusive. The higher the value the the higher the likelihood of winning. If no value is set, a default of 50 is used.


EncryptionType

REG_DWORD
USEFIPS
0


Multiexcerpt
MultiExcerptNameEncryptionType
Use of FIPS compliant encryption for communications. You must use the same setting on all PXE Everywhere Agents.
  • 0 – use default encryption
  • 1 – use FIPS encryption


Flags

REG_DWORD

This value does not have an installer property.


Registry value is not created.

If set to 1 the DHCP listener adds an ASCII terminator character to the bootfile name in the DHCP acknowledgement message. Some HP machines require this.

Any value other than 1 is treated as default 0.

IgnoreGatewayAddress

REG_DWORD

This value does not have an installer property.


Registry value is not created.

If set to any value other then 0 the DHCP listener ignores the gateway address.

If not set then assumes default 0 .

IgnoreWireless

REG_DWORD

This value does not have an installer property.



0

If set to 1 then PXE Everywhere Agent does not bind on wireless adapters.

Any value other than 1 is treated as default 0.

n/a
INSTALLDIR
%ProgramFiles%\1E\PXEEverywhere\ResponderInstallation folder.

LogFileName

REG_SZ
LOGPATH
Note
This property only specifies the location of the log file.


%ProgramData%\1E\PXEEverywhere\ PXEEverywhereResponder.log


Multiexcerpt
MultiExcerptNameLogFileName

The location of the PXE Everywhere Responder log file. The path is created if it does not exist.

The logfile name is PXEEverywhereResponder.log


LogFormat

REG_DWORD
LOGFORMAT
1


Multiexcerpt
MultiExcerptNameLogFormat

Formatting depends on which bits are set:

  • bit 0 (0x01) use Configuration Manager-compatible format (default)
  • bit 3 (0x08) do no formatting
  • bit 7 (0x80) include milliseconds in the timestamp


MaxLogFilesize

REG_DWORD
MAXLOGFILESIZE
10485760


Multiexcerpt
MultiExcerptNameMaxLogFilesize

Maximum size for the log file in bytes. Once the file reaches the specified size, a copy is made with a .lo_ extension in the same directory. A new log file will then be created.

Default is 10485760 (10 MBytes).


Mode

REG_DWORD
MODE
3


Multiexcerpt
MultiExcerptNameMode

Mode must be 3 – Responder mode


SessionTimeoutSecs

REG_DWORDThis value does not have an installer property.Registry value is not created.

Timeout for the TFTP listener. 600 if not specified or 0 is specified. Can be any positive integer value.

TftpRoot

REG_SZ
TFTPROOT
%ProgramData%\1E\PXEEverywhere\TftpRoot


Multiexcerpt
MultiExcerptNameTftpRoot

Location for the PXE Everywhere Responder TFTPROOT directory.

If you

Warning

Do not change the location

of TFTPROOT, you need to change the location that you copy the additional PXE boot files to.

of TFTPROOT. If you need to do this then please contact 1E for guidance.